12v Day Night Swtch |
|
 |
Specifications
- 12VDC operation
- Normally open and closed relay contacts 5A @ 12VDC
- Built in delay
Application
- Isolate zones or equipment during the day or at night
- Turn equipment on / off at night
- On power up, the relay will energise
- If light is detected ie. daytime, the relay will drop out after 20 seconds -
therefore the relay is energised at night |
|
| |
|
|
220v Relay on Board |
|
 |
Specifications
- 12VDC or 16VAC operation / 24v DC version available
- Current drain - 48mA energised
- Normally open & normally closed relay contacts 10A @220VAC
- Reverse polarity protection
- Back emf protection
- Physical size - 37mm x 26m
Application
- Switch 220V lighting from siren output on panel
- Switch high current from low current trigger |
|
| |
|
|
2 Zone Alarm pcb |
|
 |
Specifications
- 16V AC input
- 1A battery charger circuit
- Fused on board
- 12V DC output
- LED status output/ alarm memory armed/disarmed
- Separate panic input
- 2 zone inputs
- 1 minute timed siren output
- Physical size - 104mm x 47mm
Application
- Low cost alarm in cottage or caravan
- Simple panic unit |
|
| |
|
|
2 Zone Alarm Plastic |
|
 |
Specifications
- 6V AC input
- 1A battery charger circuit
- Fused on board
- 12V DC output
- Plastic housing with space for 1.2AH battery
- Key switch input for arm/disarm and reset
- LED status output/ alarm memory
- Built in receiver for remote arming / disarming and panic
- 2 Zone inputs
- 1 minute timed siren output
- Physical size - 140mm x 117mm x 50mm
- Separate panic input
Application
- Low cost alarm in cottage or caravan
- Simple panic unit |
|
| |
|
|
ACDC Relay on Board |
|
 |
Specifications
- Power supply - 12VDC or 16VAC
- Current drain - 38mA when energised
- Normally open and closed potential free relay contacts 10A @12VDC
- Reverse polarity protection
- Back emf protection
- Physical size - 34mm x 29mm
Application
- Isolate radio from panel to reduce false alarms
- Convert negative to positive trigger
- Switch a high current device from a low current trigger |
|
| |
|
|
Battery Connector |
|
 |
Specifications
- 6,3mm receptacles to plug on to battery
- 4,8mm lugs for battery charger wiring
- Dual screw terminals for connection to radio and/or second battery
- Physical size - 57mm x 24mm
Application
- Connecting of auxiliary equipment without cutting battery leads
- Good solid connection for radio wiring
- Easy to power down the system without losing radio connections |
|
| |
|
|
Dual Relay on Board |
|
 |
Specifications
- Power supply - 12VDC/16VAC
- Current drain - 18mA when energised
- Two independent normally open and closed relay contacts 1A @12VDC
- Reverse polarity protection
- Back emf protection
- Low voltage trigger input
- Physical size - 32mm x 32mm
Application
- Perform 2 tasks from single trigger
- Convert negative to positive trigger
- Switch a high current device from a low voltage trigger |
|
| |
|
|
Low Battery Cutout |
|
 |
Specifications
- Prevents battery from discharging completely
- Plugs directly onto 7AH battery or supplied with battery leads
- Automatically cuts power when battery voltage falls to 10,6v
- Automatically restores power to battery when charger voltage is re-applied
- LED indication
- Current rating 5A @ 12VDC
- Physical size - 59mm x 40mm
Application
- To prevent total discharge of battery on any alarm or access control installation |
|
| |
|
|
Stepper Relay |
|
 |
Specifications
- Power supply - 12VDC
- Current drain - 10mA standby current
- A pulse on key switch input changes the state of relay
- LED output indicates the state of relay
- Physical size - 45mm x 41mmo
Application
- Arm/disarm from multiple points
- Isolating of single zones
- Latching of outdoor lighting |
|
